For Idle Timeout, specify the number of minutes a nonadministrative user session may remain idle before ending. The minimum is five minutes. The default idle session limit is 10 minutes, which means that if a user’s session is inactive for 10 minutes, the system ends the user session and logs the event in the system log (unless you enable
default-idle-timeout . If you would like an "unlimited" idle time, you should set the vpn-idle-timeout in the group-policy to a specific number instead of "none" -- the maximum you can set with the vpn-idle-timeout command is 35791394 minutes (something like ~24000 days or essentially unlimited). What is the VPN device on the onprem side. There should be some setting on the VPN side for the Idle timeout. You need to be careful while setting this because it should first be checked by the device vendor before making any changes. This may cause issues with the VPN tunnel if the traffic is not there for sometime. Regards, Dipin Mathew. 1.Inactivity timeout will not work when 'Always On VPN' feature is enabled for NetExtender Connections. 2.Inactivity timeout applies to NetExtender Windows Clients only. 3.User timeout setting takes precedence over the group timeout and the group timeout takes precedence over the global timeout. We currently have our VPN users set to an 8 hour timeout. We have one supplier that needs this to be longer though. Is there any way to increase the length of time without doing it for all users? Currently running E80.81 for the client and R77.30 on our gateways. May 16, 2016 · For LAN-to-LAN profiles, the Idle Timeout is set to 300 seconds by default. It means the router will disconnect the VPN connection if it did not detect any traffic over the VPN connection for 300 seconds. If you don't want the VPN to be disconnected, enable "Always on" for Dial-out profiles. Set "Idle Timeout" to 0 for Dial-in profiles (VPN server)
You're looking for the auth timeout. It's a hard limit to the length of a SSL VPN session. Not sure if it's available in the UI, but it's available in the CLI. Time is specified in seconds, and the default (as far back as I remember) is 8 hours. You can set it to 0 to disable, but I'd strongly recommend against it for security reasons.
May 05, 2014 · 2- Click Add, Click on User Groups, click add again, then Add you VPN Users group. click next, 3- Access Granted, click next 4- keep the default authentication methods and click next, 5- click on idle time out under Constraints, check the "Disconnect after the maximum idle timeout", specify the idle timeout in minutes and click next. 6- next For Idle Timeout, specify the number of minutes a nonadministrative user session may remain idle before ending. The minimum is five minutes. The default idle session limit is 10 minutes, which means that if a user’s session is inactive for 10 minutes, the system ends the user session and logs the event in the system log (unless you enable
Setting a default Idle Timeout for any IPSec VPN Connection enables administrator to define the maximum time for which the tunnel will stay connected even if no traffic passes through. This can be done by setting a default Idle session time interval while configuring an IPSec Tunnel.
client-idle-timeout is the only option for disconnecting the vpn client connection. May be there are traffic flow between the client and protected resources even though customer is not using any application manually. There are two idle timeout settings to consider, for sessions in a established connection state: inbound through the Azure load balancer. This timeout defaults to 4 minutes, and can be adjusted up to 30 minutes. outbound using SNAT (Source NAT). This timeout is set to 4 minutes, and cannot be adjusted. There is no idle timeout configuration option for the GVPN client. They said even if we used a third party client that had that capability, it was not likely to work because of all the background chatter that goes over the VPN connection. I set up a test machine with the built in Windows VPN client and left it idle for a while. # config vpn ssl settings # set idle-timeout 300 # set auth-timout 28000 The idle-timeout is closing the SSLVPN if the connection is idle for more than 5 minutes (300 seconds). This configuration can be changed in the WebUI (SSL VPN settings) as well. The auth-timeout is closing the SSLVPN connection based on the the authentication timeout. By For Juniper VPN SSL, the default values are: Idle: 10 m Max session: 60 m reminder time: 5 I can not find best practices for Junos Pulse timeout and SSL session. If I configure the Junos Pulse session like: Idle: 60 m Max session: 180 m reminder time: 5 and If I configure the SSL session like: Idle: By default, the TCP connection timeout is 15 minutes and the UDP connection timeout 30 seconds. In order to increase the connection timeout you can modify it from the firewall access rules. NOTE: The following scenario describes how to modify the TCP connection timeout for a Site-to-Site VPN between 2 SonicWalls.